| Load Ratings |
| |
Dimmer Channels |
6 |
| |
Maximum Per Channel |
800 Watts/VA (3.5 Amps at 230 Volts AC), expandable via Expansion Modules (sold separately) |
| |
Minimum Per Channel |
25 Watts/VA (0.108 Amps at 230 Volts AC) |
| |
Module Total |
2200 Watts/VA (10 Amps at 220 Volts AC);
2300 Watts/VA (10 Amps at 230 Volts AC);
2400 Watts/VA (10 Amps at 240 Volts AC) |
| |
Dim Load Types |
LED, incandescent, magnetic low-voltage, neon/cold cathode, 2-wire dimmable fluorescent ballast |
| |
Switch Load Types |
Electronic low-voltage, 3- and 4-wire fluorescent, high-inrush switching;
277 Volt switching available via CLS-EXP Series expansion modules |
| Power Requirements |
| |
220 to 240 Volts AC, 50/60Hz, line power |
| Connections |
| |
LOCAL DEVICES |
(1) 4-pin 5mm detachable terminal block;
Cresnet® Master port for local devices including:
- C2N-DB and CNX-B Series keypads, 16 maximum;
- C2N-SSC-2 and C2N-SDC-DC shade controllers; 16 maximum;
- Additional CLSI-C6 or CLSI-C6M units, 8 maximum;
- Additional CNPWS-75 or other Cresnet power supply required beyond 4 devices; C2N-SDC-DC always requires an additional power supply
|
| |
HOT |
(1) Captive screw terminal,[1] line power input |
| |
LOAD1 – LOAD6 |
(6) Captive screw terminals,[1] dimmer channel outputs 1 – 6 |
| |
NEUTRAL |
(1) Captive screw terminal,[1] neutral input |
| |
GROUND |
(1) Captive screw terminal,[1] ground |
| |
PC (Front) |
(1) 3.5 mm TRS mini-phone jack, RS-232 programming port |
| Controls |
| |
Buttons 1 – 6 |
(6) 3-position rocker switches, configurable to recall individual scenes, to control shades, or for master lighting or shade control;
“Scene mastering” option enables manual dimming utilizing rocker button action, also used to adjust lighting levels when in “Lighting” mode and shade positions when in “Shades” mode;
Additional functionality configurable via software |
| |
Up/Down Button |
(1) 3-position rocker switch, configurable for master lighting or shade control or as a “shift” for buttons 1-6;
Additional functionality configurable via software |
| |
ON |
(1) Pushbutton, recalls “On” scene |
| |
OFF |
(1) Pushbutton, turns all lights off |
| |
LIGHTS, SHADES |
(2) Pushbuttons, select “Lights” or “Shades” modes |
| |
SAVE, CANCEL, ∧, ∨ |
(4) Pushbuttons, navigate and execute setup functions |
| |
Reset |
(1) Recessed miniature pushbutton, executes hardware reset |
| |
Dimming Ramp Rate |
5 seconds (default), software adjustable 1 to 10 seconds |
| |
Scene Fade Time |
2 seconds (default), software adjustable 0 seconds to 99 minutes |
| LED Indicators |
| |
Scenes |
(6) White LEDs, one per each “Scene” Button |
| |
High/Low |
(2) White LEDs, indicate “Shift” status |
| |
ON |
(1) White LED, indicates “On” Scene is selected |
| |
LIGHTS, SHADES |
(2) Green LEDs, indicate “Lights” or “Shades” mode is active |
| |
SAVE, CANCEL |
(2) Green LEDs, correspond with “Save” and “Cancel” buttons |
| |
MIN, SEC |
(2) Green LEDs, indicate display of “Minutes” or “Seconds” |
| |
1 – 6 |
(6) Green LEDs with bar graph logic, indicate lighting levels and shade positions |
| |
Numeric Display |
(2) 8-segment digits, indicate modes and setup values |
| IR Receiver |
| |
Reception Frequency |
36 kHz |
| |
Requires CLS-IRHT8 IR remote |
| RF Wireless |
| |
RF Transceiver |
2-way RF, 2.4 GHz ISM Channels 11-26 (2400 to 2483.5 MHz), IEEE 802.15.4 compliant |
| |
Range (Typical) |
150 feet indoor, 250 feet outdoor;
Subject to site-specific conditions;
Range is increased by adding additional devices or C2NI-MNETRPT repeater |
| |
Gateway |
Requires a C2N-MNETGW RF gateway |
| Environmental |
| |
Temperature |
32° to 104° F (0° to 40° C) |
| |
Humidity |
10% to 90% RH (non-condensing) |
| Enclosure |
| |
Mounts in a 4-gang electrical box, 3-1/2" deep minimum |
| Dimensions |
| |
Height |
4.48 in (114 mm) |
| |
Width |
8.89 in (226 mm) |
| |
Depth |
2.47 in (63 mm) |
| Weight |
| |
1.43 lb (0.65 kg) |
